How to Manually Raise Your Volvo Penta Outdrive – A Step-by-Step Guide
To manually raise a Volvo Penta outdrive, adjust the trim tabs to their highest setting and then turn the engine off.
How To Manually Raise Volvo Penta Outdrive
Raising your Volvo Penta Oubdrive is an important step required for various water activities and boat maintenance. This guide will provide you with the tools and information to get your outdrive up and running quickly and safely. Firstly, disconnect all power sources before making any adjustments to the outdrive. Loosen the trim tabs by rotating them counter-clockwise, then raise the outdrive slowly by pressing the up button on the remote control until it reaches the desired angle. Make sure that the trim limit switch is engaged when the outdrive is fully raised, which will prevent it from moving higher. Finally, inspect all parts of the outdrive for any loose or missing components, and ensure that it is securely connected to the stern or drive pack. With these steps, you will have safely raised your Volvo Penta Outdrive!
Removing The Boat Cover
Before you can begin to manually raise your Volvo Penta outdrive, it is important to make sure the area surrounding the outdrive is clear of any debris. This includes removing the boat cover that is commonly used to protect the outdrive from elements. Once the boat cover has been removed, you will need to disconnect any power connections that are connected to the battery cables.
Removing and Draining Outdrive Coolant
In order to manually raise your Volvo Penta outdrive, you will need to drain any coolant that has been filled in the outdrive. To do this, you will need to locate the coolant fill port and drain plug on the outdrive before draining any coolant into a bucket or pan.
Raising The Outdrive With Lever Arm Tool
Once all of the coolant has been drained from the outdrive unit, you are ready to begin manually raising your Volvo Penta outdrive with a lever arm tool. You will need to tighten the lever arm onto the splines of the council before lifting it up until it is securely locked into position inversion bracket slots.
Checking and Adjusting Propeller Clearance From Hull if Necessary
Once your Volvo Penta Outdrive has been raised, you will want to check and adjust propeller clearance from hull if necessary. To do this, simply loosen clevis pins and correctly align propeller on shaft before tightening clevis pins again in order to secure propeller onto shaft.
Reconnecting Power Connections To Outdrive Unit Including Angle Sensor And Trim/Tilt Sensors
The last step in manually raising your Volvo Penta Outdrive unit is reconnecting power connections including angle sensor and trim/tilt sensors. This includes connecting wires on backside of outdrive unit, angle sensor and trim/tilt sensors before reattaching battery cables again onto power source in order for your boat engine system to be operational again.
Cleaning Exterior of Outdrive unit
Cleaning the exterior of an outdrive unit is an important part of maintaining its functioning. This can be done by simply wiping down the outdrive with a soft cloth or a brush with a mild detergent. This will help to ensure that any dirt or debris that may have accumulated on the exterior of the outdrive is removed, and helps to keep it looking its best.
Draining Fitting Internal Seals of Gear Oil From Lower Legs on the Outdrive
When raising a Volvo Penta OutDrive, it is important to ensure that all internal seals of gear oil from the lower legs are drained correctly. This can be done by checking engine oil levels in each leg of the lower unit to make sure they match with the oil level indicators. If necessary, oil filters should be replaced as well.
Replenishing Oil Reservoir With Fresh GearOil
Once all internal seals for gear oil have been drained from the lower legs, it is important to replenish the oil reservoir with fresh gearoil. This will help ensure optimal operation and performance when running your Volvo Penta OutDrive. It is also important to replace any lower gearoil seals that may have worn out during this process, thus completing the manual raising of your Volvo Penta OutDrive.
FAQ & Answers
Q: How do I manually raise a Volvo Penta Outdrive?
A: To manually raise a Volvo Penta Outdrive, first remove the boat cover and clear the area of debris. Next, disconnect the power boat battery cables. Then, locate and drain outdrive coolant into a bucket or pan. After that, raise the outdrive with lever arm tool. Secure it in position with an inversion bracket slot. Check and adjust propeller clearance from hull if necessary. Reconnect power connections to outdrive unit including angle sensor and trim/tilt sensors. Clean the exterior of the outdrive unit. Lastly, drain gear oil from lower legs on the outdrive, check engine oil levels in each leg of lower unit, replace oil filters if necessary, replenish oil reservoir with fresh gear oil and replace lower gear oil seals to complete manual raising of Volvo Penta OutDrive.
Q: What is an inversion bracket slot?
A: An inversion bracket slot is used to securely lock the outdrive into position after it has been raised using a lever arm tool.
Q: What should I do after raising the OutDrive?
A: After raising the OutDrive, check and adjust propeller clearance from hull if necessary. Reconnect power connections to outdrive unit including angle sensor and trim/tilt sensors. Clean the exterior of the outdrive unit. Lastly, drain gear oil from lower legs on the outdrive, check engine oil levels in each leg of lower unit, replace oil filters if necessary, replenish oil reservoir with fresh gear oil and replace lower gear oil seals to complete manual raising of Volvo Penta OutDrive.
Q: How do I clean the exterior of an OutDrive?
A: To clean the exterior of an OutDrive, wipe it down with a soft cloth or brush with mild detergent until it is free from dirt and debris buildup.
Q: How do I replenish an Oil Reservoir?
A: To replenish an Oil Reservoir after manual raising of a Volvo Penta OutDrive, use fresh gearoil to fill up any gaps between levels as indicated by indicators inside each leg on lower units. Replace any old or worn-out filters before refilling for optimal performance results
In conclusion, manually raising your Volvo Penta Outdrive can be a difficult task, but is achievable with the right tools and knowledge. With the right steps and proper maintenance, you can have your outdrive raised and ready to go in no time.